To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3. The mouse function control is enabled using the USB cable to connect your computer and the projector. Control the degree of difference between Contrast the lightest and darkest parts of the picture.
The projector will automatically detect the source. When OSD is displayed, use keys to select any item in the main menu. Presentation: Good color and brightness from PC input. Page 24 User Controls Image Saturation Adjust a video image from black and white to fully saturated color. Individual color adjustments for Cyan, Magenta, Yellow can also be adjusted.
Page 26 User Controls Image Advanced Degamma This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. The projector will not search inputs that are de-selected. Overscan the image to remove video encoding noise on the edge of video source.
Zoom Press the to reduce the size of an image. Press into the sub menu and then use the key to select your preferred language.
Change Password 1. If you experience an unstable or flickering image, use this function to correct it. Source Lock On: The projector will search specified connection port. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp. Page Appendices Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information.
If a problem persists, please contact your local reseller or service center. Ensure all the pins of connectors are not bent or broken. Page 42 Appendices 6. Verify that the resolution setting of the monitor display is lower than or equal to UXGA x Page 43 Appendices Image is out of focus Make sure the lens cap is removed. See page Move to within 6 m 20 ft of the projector. When the lamp life is nearing the end of use, you will receive a warning message.
When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 min- utes before changing the lamp.
Page 48 Appendices Lamp Replacement Procedure: 1. Allow the projector to cool down for at least 30 minutes. Disconnect the power cord. Use a screwdriver to unscrew the 2 screws from the cover.
If you wish to use a third party ceiling mount kit, please ensure the screws used to attached a mount to the projec Service : services optoma. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Print page 1 Print document 54 pages. Rename the bookmark. Delete bookmark? Please check your email for further instructions. Enter a new password. SAFETY The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance.
See projector enclosure for safety related markings. Warning Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be closely supervised when viewing these images. Photosensitive Seizure Warning and Other Health Risks Some viewers may experience an epileptic seizure or stroke when exposed to certain flashing images or lights contained in certain Projector pictures or video games.
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Trademark Recognition Kensington is a U. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver. Notice:: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation is subject to the following two conditions: 1.
This device may not cause harmful interference and 2. Remarque l'intention des utilisateurs canadiens Cet appareil numerique de la classe B est conforme a la norme NMB du Canada.
Optional accessories. No Item 1. Lamp Cover 2. Focus Ring 3. Zoom Lever 4. IR Receiver 5. Keypad 6. Tilt-Adjustment Foot 7. Security Bar. No Item 8. Lens 9. Ventilation inlet Ventilation outlet Kensington TM Lock Port Power Socket HDMI 1 Connector 2. Kensington TM Lock Port 8. Power Socket Note: Remote mouse requires special remote control. Lamp LED 3. Keystone Correction 4. Temp LED 5. Information 6.
No Item 7. Enter 8. Menu 9. Source Power On 2. User 2 3. User 1 4. Brightness 5. Keystone 6. Mute 7. DB Dynamic Black 8. Source 9. Enter Menu HDMI1 VGA1 not supported VGA2 not supported Power Off. No Item User 3 Contrast Display Mode Aspect Ratio Sleep Timer Re-Sync Volume - HDMI2 YPbPr not supported Video not supported. Freeze 3. Mouse Left Click 5.
Enter 6. Laser 7. Page - 8. HDMI User 2 User 1 Brightness Mode Mute Mouse Right Click VGA Video Numeric Keypad Table mount front Table mount rear. Ceiling mount front Ceiling mount rear. How to determine projector location for a given screen size, please refer to distance table on pages HDMI Cable 2. Audio Out Cable 6. USB Cable mouse control 7. USB Power Cable 8. HDMI Dongle 9. Power Cord. Tilt-Adjustment Feet Tilt-Adjustment Ring Zoom and focus To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease the projected image size.
Effective range Infra-Red IR remote control sensor is located on the top side and front side of the projector. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. About the Optoma GT Optoma GT specifications. Related product manuals. What is the weight of the Optoma GT? The Optoma GT has a weight of g.
What is the height of the Optoma GT? The Optoma GT has a height of mm. What is the width of the Optoma GT? The Optoma GT has a width of mm. What is the depth of the Optoma GT? The Optoma GT has a depth of mm. Is the manual of the Optoma GT available in English?
0コメント